Wilbur-curtis TXSG1501S600 Manuel d'utilisateur télécharger pdf

WARNING – THERMOPRO SERVERS MAY BE HEAVY WHEN FILLED. CARE MUST BE TAKEN WHEN TRANSPORT-

ING TO AVOID DROPPING OR SPILLING.

Use only coffee or water in the insulated dispenser. Do not use the ThermoPro server to dispense any other beverage. Preheating

is recommended.

1. Place a clean and empty server centered under one of the brewcones of your coffee brewer.

2. Make sure the screen reads READY TO BREW.

3. Fill brewcone with the correct measure of ground coffee for the intended volume of brewed coffee.

4. Select the brew button that matches the brew volume and press to brew into the coffee dispenser.

5. Allow coffee in the brewcone to drip completely before removing the insulated dispenser.

SERVICING THE THERMOPRO SERVER

1. Completely drain the unit of any coffee.

2. Allow server to cool.

3. Unscrew and remove the lid and tube assembly.

REPLACING THE GAUGE GLASS

The gauge glass can be removed for maintenance and cleaning. Refer to the illustration on page three [3] for assembly sequence.

1. Unscrew the vented cap plug from the top of the gauge glass shield.

2. Carefully lift out the gauge glass tube from the shield and scrub inside the glass with a tube cleaning brush and mild

detergent solution. Inspect the glass tube for cracks or chips. If broken, carefully remove all traces of glass and then insert

a new gauge glass tube.

3. Check the top and bottom washers that make the tube water tight. Clean the washers. Make sure they are not leaking.

Replace if necessary.

4. With the sight glass seated in the gauge glass shield, thread the cap plug onto the top of the shield. Do not overtighten.

REMOVING THE BASE & BOTTOM COVER

 Toreplacethesiliconeelbowttingforrepairorcleaning:

1. Remove the base assembly. Press down on the slide tab on the back side of the stand and lift off the

server section.

2. Turn the server upside down and take off the plastic bottom cover. This will reveal the silicone elbow

 tting.

3. Remove the wire hose clamps by squeezing the wire ears together. While holding the clamp open,

loosen the soft silicone elbow from the liner drain pipe and the faucet shank and pull out elbow.

4. Check for leaks and replace with a new part if necessary.

5. Reverse these steps to assemble.

REMOVING THE FAUCET

The faucet will require periodic cleaning and maintenance.

1. Remove the faucet from the body of the server. Unscrew the large nut holding the faucet to the shank to

take off faucet.

2. Disassemble the faucet. Unscrew the bonnet from the body of the faucet.

3. Remove the faucet handle by pressing inward on the seat cup (see photo at right) then unhooking the

handle from the center shaft.

4. The seat cup, center shaft and spring will now separate from the bonnet. Clean these parts with a mild

detergent solution.

5. While you have these parts for cleaning, check the seat cup for tearing of splitting. Make sure the faucet

spring is free of corrosion. Replace with repair kit if necessary (item 13, page 3).

ASSEMBLY

Assemble the unit by reversing the steps for disassembly. Finger tighten only wing nut for faucet. Make sure clamps are fastened

properlyandsiliconettingsareingoodcondition.Onceassembled,checkforleaksaroundthettingandfaucet.

Wilbur Curtis Company, inC.

TXSG – Service Manual

ModelsIncluded:

TXSG0101S600 TXSG1501S600

1 2 3 4

Résumé du contenu

Page 1 - TXSG – Service Manual

1WARNING – THERMOPRO SERVERS MAY BE HEAVY WHEN FILLED. CARE MUST BE TAKEN WHEN TRANSPORT-ING TO AVOID DROPPING OR SPILLING.Use only coffee or water in

Page 2 - Rough-In Drawing

2 CAUTION Do not immerse in water. Do not place in dishwasher. Do not use harsh powders or cleansers containing chlorine.Cleaning Instructions

Page 3 - ThermoPro Gravity Pot

319202122A22238910111213141516 171818A24251272345672628Illustrated Parts ListIllustrated PartsThermoPro Gravity PotAll parts are common between the 1

Page 4 - Product Warranty Information

4ECN 12581.9/7/[email protected] 12572 . 9/1/[email protected] . revGECN 12489 . 7/23/10 @ 9.5 . rev FECN 12161 . 2/18/10 @ 12.9 . rev EECN 10341 . 3/18/9 @ 15.3

Modèles reliés TXSG0101S600

Commentaires sur ces manuels

Pas de commentaire

Wilbur-curtis TXSG1501S600 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chaudière à eau Wilbur-curtis TXSG1501S600. Wilbur Curtis TXSG1501S600 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés TXSG0101S600

Commentaires sur ces manuels