Wilbur-curtis TLP61 Manuel d'utilisateur télécharger pdf (Page 9)

Error Codes are reset by turning the rear toggle switch to Standby for a minimum of 10 seconds, then returning

the switch to ON. Any service required for your Curtis system must be performed by a qualified service

technician.

TROUBLE-

SHOOTING

GUIDE

ERROR CODES

Curtis ADS Systems contain various safety features in the electronic circuitry that will

shut down the functions of the unit in the event of systems faiolures. Error codes are

signalled by the red READY-TO-BREW light blinking.

INTERPRETING THE CODES

ADS technology features a state-of-the-art error code system. This is designed to quickly advise you of any problems the

system may experience expediting service or repair. Occasionally, an error reported may be a problem with the water

supply or electrical power; NOT directly associated with a fault of the Curtis system itself. An example of this includes a

clogged water filter — indicated by a water level error code.

Error Codes are indicated by blinking. = Long Flash = Short Flash

The code pattern is as follows:

WATER LEVEL PROBLEM

TEMPERATURE PROBLEM

READY TO BREW

1. Water line has been turned OFF

2. Insufficient Water Supply;

Water Line Pinched

3. Clogged Water Filter

4. Defective Inlet Valve

5. Grounded Probe

6. Defective Control Board

Turn ON Water Line; confirm unit is turned on

and water is flowing into heating tank.

Straighten Wafer Line; confirm unit is turned on

and water is flowing into heating tank.

Replace filter; confirm unit is turned on and water

is flowing into heating tank.

Contact Factory.

SYMPTOM:SYMPTOM:

SYMPTOM:

TER DOES NOT FLOW INTO HEATER DOES NOT FLOW INTO HEA

TER DOES NOT FLOW INTO HEA

TING TING

TING

ANKANK

ANK

POSSIBLE CAUSE SOLUTION

Water Level

ERROR CODE

SYMPTOM:SYMPTOM:

SYMPTOM:

TER HEATER HEA

TER HEA

TING TING

TING

ANK OVERFLOWINGANK OVERFLOWING

ANK OVERFLOWING

POSSIBLE CAUSE SOLUTION

Water Level

ERROR CODE

7. Defective Water Inlet Valve

8. Limed-Up Probe

9. Non-grounded or loose terminal

connections at control board or

tank.

10. Defective Control Board.

Turn power off and observe tank water level. If water continues to

flow Inlet Valve must be cleaned, rebuilt or replaced.

Clean and/or replace.

The control board must be securely grounded for proper operation.

Check for loose connections at the terminals.

Contact Factory

SYMPTOM:SYMPTOM:

SYMPTOM:

TER IN HEATER IN HEA

TER IN HEA

TING TING

TING

ANK DOES NOT GET HOTANK DOES NOT GET HOT

ANK DOES NOT GET HOT

;;

;

TER TER

TER

TEMPERATEMPERA

TEMPERA

TURE LOWTURE LOW

TURE LOW

POSSIBLE CAUSE SOLUTION

11. Defective or Loose Heat Sensor

12. Defective Heating Element

13. Defective Control Board

Make sure there is a layer of silicone paste (Part No WC-5231)

between the sensor and tank body. The fastening nut should be

securely tightened, making a good connection. Check wire for

damage.

Contact factory.

Temp Sensor

ERROR CODE

IMPORIMPOR

IMPOR

ANTANT

ANT

Error codes are

indicated by the

red READY TO

BREW light. If and

Error Code occurs,

the unit will shut

down all functions

including heating,

water inlet, water

delivery.

ALWAYS

confirm Error

Code three times.

IMPORTANT:

Heating function

may be SHUT

DOWN due to

Water Level Error

Code.

ADS ERROR CODESADS ERROR CODES

ADS ERROR CODES

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Wilbur-curtis TLP61 Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à café Wilbur-curtis TLP61